Marine Navigation & Equipment

HRP05-12 Hydraulic Reversing Pump Unit 12 VDCThe Accu-Steer HRP Series pump sets are designed to interface hydraulic steering systems with autopilot and electric steering controls. The output flow from the pump set determines the speed of the rudder. These three pumps interface with most autopilots.FeaturesHRP05 outputs 0.5 cu in/secRugged compact constructionUnit mounts easilyGerotor gear technology ensures "Whisper Quiet" operationAdjustable flow controlBuilt-in Pressure relief valve ...

HRP05-24 Hydraulic Reversing Pump Unit 24 VDCThe Accu-Steer HRP Series pump sets are designed to interface hydraulic steering systems with autopilot and electric steering controls. The output flow from the pump set determines the speed of the rudder. These three pumps interface with most autopilots.FeaturesHRP05 outputs 0.5 cu in/secRugged compact constructionUnit mounts easilyGerotor gear technology ensures "Whisper Quiet" operationBuilt-in Pressure relief valve ...

HRP11-12 Hydraulic Reversing Pump Unit 12 VDCThe Accu-Steer HRP Series pump sets are designed to interface hydraulic steering systems with autopilot and electric steering controls. The output flow from the pump set determines the speed of the rudder. These three pumps interface with most autopilots.FeaturesHRP11 outputs 1.0 cu in/secRugged compact constructionUnit mounts easilyGerotor gear technology ensures "Whisper Quiet" operationBuilt-in Pressure relief valve ...

HRP11-24 Hydraulic Reversing Pump Unit 24 VDCThe Accu-Steer HRP Series pump sets are designed to interface hydraulic steering systems with autopilot and electric steering controls. The output flow from the pump set determines the speed of the rudder. These three pumps interface with most autopilots.FeaturesHRP11 outputs 1.0 cu in/secRugged compact constructionUnit mounts easilyGerotor gear technology ensures "Whisper Quiet" operationAdjustable flow controlBuilt-in Pressure relief valve ...

HRP17-12 Hydraulic Reversing Pump Unit 12 VDCThe Accu-Steer HRP Series pump sets are designed to interface hydraulic steering systems with autopilot and electric steering controls. The output flow from the pump set determines the speed of the rudder. These three pumps interface with most autopilots.FeaturesHRP17 outputs 1.6 cu in/secRugged compact constructionUnit mounts easilyGerotor gear technology ensures "Whisper Quiet" operationBuilt-in Pressure relief valve ...

HRP17-24 Hydraulic Reversing Pump Unit 24 VDCThe Accu-Steer HRP Series pump sets are designed to interface hydraulic steering systems with autopilot and electric steering controls. The output flow from the pump set determines the speed of the rudder. These three pumps interface with most autopilots.FeaturesHRP17 outputs 1.6 cu in/secRugged compact constructionUnit mounts easilyGerotor gear technology ensures "Whisper Quiet" operationBuilt-in Pressure relief valve ...

HRP35-12 Hydraulic Reversing Pump Unit - 12 VDCThe Accu-Steer HRP100 The Accu-Steer HRP100 pump set is designed to interface hydraulic steering systems with autopilot or electric steering control systems. The output flow from the pump set determines the speed of the rudder. The output flow of the HRP100 is adjustable between 0 and 3.5 cu. in. per second. The pump has built-in pressure relief valves, which are factory set at 500 psi. This pump is recommended for medium-duty applications on...

HRP35-24 Hydraulic Reversing Pump Unit - 24 VDCThe Accu-Steer HRP100 The Accu-Steer HRP100 pump set is designed to interface hydraulic steering systems with autopilot or electric steering control systems. The output flow from the pump set determines the speed of the rudder. The output flow of the HRP100 is adjustable between 0 and 3.5 cu. in. per second. The pump has built-in pressure relief valves, which are factory set at 500 psi. This pump is recommended for medium-duty applications on...

KVR-3 Verado Kit3' Hoses & Fittings for Furuno & Accu-Steer HRP 11/17

KVR-6 Verado Kit6' Hose & Fitting for Furuno & Accu-Steer HRP 11/17

2886 AISLink Personal AIS Man Overboard BeaconAdvanced Automatic Identification System (AIS) technology comes to the rescue with this compact and affordable man overboard beacon with integrated Digital Selective Calling (DSC) and GPS. Unlike a personal locator beacon, which signals orbiting search and rescue satellites, AISLink sends an alert message within seconds to all local vessels with an AIS receiver and/or AIS-enabled plotter. The DSC alarm on your vessel's VHF can also be...

AISLink CA1 Data CableA 1m (3.3ft) long, 50 way data cable to connect the transceiver serial data ports to the junction box.

AISLink CA1 Power CableA 2m (6.6ft) long power cable to supply the transceiver. The power cable also includes alarm output connections.

AISLink CB1 Power/Data CablePower and Data Cable specifically for ACR's AISLink CB1 Class B Automatic Identification System.

GPS Interface Cable for 2875 Sat 3 EPIRBOptical GPS interface cable - Cat II. This connects the Satellite3 406 to your vessel's GPS receiver to continuously update and store precise position data. GPS positioning provides SAR notification typically within 2-15 minutes.

OPTO-4 Isolated NMEA to RS232 AdapterIsolate an RS232 (PC) port to protect against ground loops...The Actisense OPTO-4 is a bi-directional NMEA 0183 (RS422) to RS232 interface cable which provides a safe method of connecting an NMEA 0183 system to a laptop PC or any device with a standard RS232 9-pin port. The isolation protects the connected device, so any potentially hazardous voltages on the NMEA 0183 bus do not cause damage to the PC hardware, offering the user complete peace of mind. The...

117WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B117B150B744VB744VLB765CSS555 ...

117WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings.You can use wrench 117WR-4 to brace the housing when using this wrench.For use with:B117 B150 B744V B744VL B765C SS555

117WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B117B150B744VB744VLB765CSS555 ...

117WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. For 2" bronze and stainless steel housings (P617V, B617V, SS617V).Use wrench 117WR-2 or 117WR-3 for the hull nut.*Note that this wrench will not fit on the CA500 camera housing.

164WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B164SS164B175CSS164 ...

164WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on B164, SS164 and SS264 housings.You can use wrench 164WR-4 to brace the housing when using this wrench.For use with:B164SS164SS264

164WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B164SS164B175CSS264 ...

175WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the top of the housing to facilitate tightening of the hull nut. Use wrench 164WR-2 or 164WR-3 for the hull nut.For use with:B164B175SS164SS264IMPORTANT: the design of the housing for these transducers changed slightly in June 2012. This wrench is for the newer design and has an internal width of 2-3/4". If you need a wrench for the older designs then use the 164WR-4 instead,...

60WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:SS60B60

60WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 60WR-4 to brace the housing when using this wrench.For use with:B60SS60

60WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B60SS60

60WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut.Use wrench 60WR-2 or 60WR-3 for the hull nut.For use with:B60SS60

75WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B75SS75

75WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on bronze and stainless steel housings. You can use wrench 75WR-4 to brace the housing when using this wrench.For use with:B75SS75

75WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B75SS75

75WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. Use wrench 75WR-2 or 75WR-3 for the hull nut.For use with:B75SS75

B164 1kW 0° Thru-Hull Transducer with Blue ConnectorThe B164 is a 1kW bronze low-profile transducer with a fast-response temperature sensor. The transducer is ideal for fast, trailered, tournament, sport-fishing boats that cannot install an external fairing. This version has a zero degree tilt for hull deadrise angles of 0-7 degrees.The BL (Blue Connector) version of the B164 transducer is for Lowrance fishfinders and sounders that use the standard Lowrance 7-pin blue connector. This...

B258, SS258 High Speed Fairing BlockAirmar High Speed Fairing block for B258, SS258 Style Transducer

Deadrise Angle Finder - Accuracy of ± 1/2°Quickly measures boat hull deadrise angle.Accuracy of ± 1/2°

Airmar DT812BV-235-N2 235 kHz Low Profile Tilted Element™ Smart™ Sensor 12° Tilt Bronze NMEA 2000Airmar has taken its proven Tilted Element™ and broadband technologies and applied them to its leading line of Smart™ Sensors. The DT800 is a low-profile, retractable, thru-hull sensor that computes accurate depth and temperature data and sends it to any NMEA 0183 or NMEA 2000® display. The DT800 operates at a frequency of 235 kHz and can run simultaneously with other...

Airmar DT820BV-235-N2 235 kHz Low Profile Tilted Element™ Smart™ Sensor 20° Tilt Bronze NMEA 2000Airmar has taken its proven Tilted Element™ and broadband technologies and applied them to its leading line of Smart™ Sensors. The DT800 is a low-profile, retractable, thru-hull sensor that computes accurate depth and temperature data and sends it to any NMEA 0183 or NMEA 2000® display. The DT800 operates at a frequency of 235 kHz and can run simultaneously with other...

Transom Mounting Bracket for P66 Transducer - 2004 & up

Use this cable to connect a PB150, PB200, WX100 G2183, H2183 and GH2183 ro a NMEA2000® network.

Use this cable to connect a PB150, PB200, WX100 G2183, H2183 and GH2183 ro a NMEA2000® network.

Use this cable to connect a PB150, PB200, WX100 G2183, H2183 and GH2183 ro a NMEA2000® network.

Use this cable to connect a PB150, PB200, WX100 G2183, H2183 and GH2183 ro a NMEA2000® network.

NMEA 2000 90° Elbow ConnectorAncor's NMEA 2000 Approved 90 degree elbow makes cable routing easier. The connector is installed between two cables to reduce stress on the cables and create a compact installation.Features:Color coded for easy installation and component identificationNMEA 2000 Approved, 100 percent universal and compatible with other manufacturers' products WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State...

NMEA 2000 Backbone Cable - 0.5MAncor's NMEA 2000 Approved Backbone Cables offer connection to an NMEA 2000 tee connector. The yellow couplers connect to the corresponding Ancor tees creating a simplified, color coded network installation. The backbone cables are available in four lengths from 0.5 meter (1.6 feet) to 10 meters (32.8 feet) to cover a wide variety of applications.Features:Color coded for easy installation and component identificationLarge 18 AWG power conductors to reduce voltage...

NMEA 2000 Backbone Cable - 10MAncor's NMEA 2000 Approved Backbone Cables offer connection to an NMEA 2000 tee connector. The yellow couplers connect to the corresponding Ancor tees creating a simplified, color coded network installation. The backbone cables are available in four lengths from 0.5 meter (1.6 feet) to 10 meters (32.8 feet) to cover a wide variety of applications.Features:Color coded for easy installation and component identificationLarge 18 AWG power conductors to reduce voltage...

NMEA 2000 Backbone Cable - 2MAncor's NMEA 2000 Approved Backbone Cables offer connection to an NMEA 2000 tee connector. The yellow couplers connect to the corresponding Ancor tees creating a simplified, color coded network installation. The backbone cables are available in four lengths from 0.5 meter (1.6 feet) to 10 meters (32.8 feet) to cover a wide variety of applications.Features:Color coded for easy installation and component identificationLarge 18 AWG power conductors to reduce voltage...

NMEA 2000 Backbone Cable - 5MAncor's NMEA 2000 Approved Backbone Cables offer connection to an NMEA 2000 tee connector. The yellow couplers connect to the corresponding Ancor tees creating a simplified, color coded network installation. The backbone cables are available in four lengths from 0.5 meter (1.6 feet) to 10 meters (32.8 feet) to cover a wide variety of applications.Features:Color coded for easy installation and component identificationLarge 18 AWG power conductors to reduce voltage...

NMEA 2000 Drop Cable - 0.5MAncor's NMEA 2000 Approved Drop Cables offer connection between an NMEA 2000 device and tee connector. The black couplers connect to the corresponding Ancor tees creating a simplified, color coded network installation. The drop cables are smaller in diameter and more flexible than backbone cables for easy connection to NMEA 2000 devices. The drop cables are available in four lengths from 0.5 meter (1.6 feet) to 5 meters (16.4 feet) to cover a wide variety of...